Visit Homepage

 

 

Do you find yourself looking for answers around How to Install a Bathtub?

Mounting a bath tub isn't precisely brain surgery, but it does need strong plumbing, woodworking, and in some cases, tiling skills. Replacing an old tub with a brand-new one is also a moderately challenging task. If the old bathtub is readily accessible, the project can move immediately; if you need to open up a wall surface to remove the old tub as well as place the brand-new bath tub, the job is a lot harder. In either instance, the project is within a home handyman's skills, although you will certainly need a helper to leave the old bathtub and also embeded in the brand-new one. Make sure you have actually certified yourself for the job and are comfortable trying it. Rather than working with a contractor to take over a halfway-completed task, it is far better to take into consideration using one before you begin. Possibilities are you may need an expert plumber to make tube connections.
This short article will help you install a new bathtub in your restroom if you have already bought a brand-new bathtub and also do not require to transform the plan of your previous water system pipelines.
Your tools as well as material checklist ought to comprise the following:

 

• New Bathtub


• Hammer


• Pipe Wrenches


• Prybar


• Safety Glasses


• Degree


• Pliers


• Flexible Wrench


• Putty Knife


• Screwdriver


• Cold Chisel


• Tape Measure


• Pipe Caps


 

Preparing for the Installment

First of all, the supporting frame provided with the bathroom must be fitted (if needed) according to the producer's instructions. Next, fit the faucets or mixer to the tub. When fitting the tap block, it is important to see to it that if the tap comes with a plastic washer, it is fitted in between the bathroom as well as the taps. On a plastic bathroom, it is likewise practical to fit a supporting plate under the faucets system to avoid strain on the bath tub.
Fit the versatile tap connectors to the bottom of both taps using 2 nuts and also olives (often supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the electrical outlet through the hole in the bathroom. Utilize the nut supplied by the supplier to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the versatile overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bath. See to it you utilize all of the provided washers.
Attach the trap to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Link the bottom of the overflow tube in a comparable manner.The bath must now be ready to be suited its final setting.

 

 

Removing Old Touches

If you need to change old taps with new ones as a part of your installment, then the first thing you must do is separate the supply of water. After doing so, switch on the faucets to drain any type of water continuing to be in the system. The process of eliminating the existing faucets can be quite troublesome because of the limited access that is typically the situation.
Make use of a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that links the supply pipes to the taps. Have a towel ready for the remaining water that will certainly originate from the pipes. Once the supply pipes have actually been gotten rid of, use the exact same device to loosen up the nut that holds the faucets onto the bath/basin. You will need to quit the solitary faucets from turning during this process. When the faucets have actually been removed, the holes in the bath/basin will have to be cleaned up of any old securing substance.
Before going on to fit the new taps, contrast the pipeline connections on the old taps to the new faucets. If the old faucets are longer than the new taps, after that a shank adapter is needed for the new taps to fit.

 

 

Setting up the Bath tub

Using the two wood boards under its feet, position the bath tub in the required setting. The wood boards are handy in evenly spreading the weight of the tub over the area of the boards rather than focusing all the weight onto 4 tiny factors.
The following goal is to guarantee that the bath tub is leveled all round. This can be achieved by checking the spirit level and also adjusting the feet on the bathtub up until the level reviews degree.
To mount taps, fit the bottom of the outermost adaptable faucet adapter to the appropriate supply pipe by making a compression join; then do the exact same for the other tap.
Turn on the water system as well as inspect all joints as well as brand-new pipework for leakages and also tighten them if essential. Load the bath tub as well as additionally examine the overflow electrical outlet and also the normal electrical outlet for leakages.
Ultimately, fix the bathroom paneling as defined in the supplier's user's manual. Tiling and also securing around the tub must wait up until the tub has been used at the very least when as this will certainly resolve it right into its final setting.

 

 

Fitting New Taps

If the tails of the new faucets are plastic, after that you will certainly require a plastic port to avoid damage to the thread. One end of the adapter fits on the plastic tail of the faucet and also the various other end offers a connection to the existent supply pipes.
If you require to fit a monobloc, then you will certainly need decreasing couplers, which links the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
Next off, place the faucet in the installing hole in the bath/basin guaranteeing that the washers remain in location between the tap and also the sink. Safeguard the tap in place with the manufacturer provided backnut. As soon as the faucet is safely in place, the supply pipelines can be linked to the tails of the taps. The faucets can either be linked by utilizing corrugated copper piping or with typical tap connectors. The former kind ought to be attached to the faucet ends initially, tightening up only by hand. The supply pipes can later on be linked to the other end. Tighten up both ends with a spanner after both ends have been attached.

 

 

Tiling Around the Tub

In the area where the bathroom satisfies the tile, it is essential to seal the accompanies a silicone rubber caulking. This is necessary as the installation can move sufficient to break a stiff seal, causing the water to pass through the wall in between the bathroom and also the tiling, resulting in complications with moisture and feasible leaks to the ceiling listed below.
You can select from a selection of coloured sealants to assimilate your components as well as fittings. They are sold in tubes and also cartridges, as well as can sealing voids as much as a size of 3mm (1/8 inch). If you have a larger void to fill up, you can load it with twists of drenched newspaper or soft rope. Bear in mind to always fill up the bathtub with water prior to securing, to enable the activity experienced when the tub remains in use. The sealer can crack relatively very early if you do not take into consideration this movement before sealing.
Conversely, ceramic coving or quadrant ceramic tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are also quickly offered on the marketplace. It is recommended to fit the floor tiles using water-resistant or water-proof adhesive as well as cement.

 

A Step-by-Step Guide to Installing a Bathtub

 

Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.

But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.

This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.

 

Remove the Existing Bathtub

 

To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.

The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.

 

Choose the Right Bathtub

 

The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.

 

Install the Plumbing and Ledger Board

 

You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.

Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.

 

Install the Bathtub

 

When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.

Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.

If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.

 

Hook up the Plumbing

 

Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.

 

Install the Bathtub Surround

 

A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.

Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.

If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.

If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/

 

As an avid person who reads on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround, I thought sharing that piece of content was sensible. Kindly set aside a second to share this blog posting if you enjoyed it. Thank you so much for your time spent reading it.

Information Here